P2 SMD Screen — clean image quality at scale.
P2 is the indoor pitch that scales — large lobby walls, retail anchors, conference halls, and signage projects where the brief needs sharp content over big square footage at a workable budget.
P2 is an indoor LED screen with 2 mm between pixels — about 250,000 pixels per square metre. It is widely used for large lobby walls, retail anchor displays, conference halls, and big indoor signage where viewers stand or sit 3–7 m away. P2 is around 15–20% cheaper than P1.8 and lets you build noticeably larger walls within the same budget. From 3 m+, the visual difference vs P1.8 is minimal.
P2 at a glance.
Indicative tier-1 module specifications. Exact figures depend on cabinet brand and configuration — confirmed at quote stage.
- Pixel pitch2.0 mm
- Pixel density~250,000 px/m²
- Brightness600 – 900 nits
- Refresh rate3,840 Hz minimum
- Scan mode1/26 scan
- Viewing angle160° / 160°
- IP ratingIP30
- Cabinet depth75 – 90 mm
- Service life~100,000 hrs
- MaintenanceFront access
Where P2 earns its place.
Pixel pitch is set by the closest viewer. Roughly 10× the pitch in millimetres gives the minimum comfortable distance — P2 sits in this zone.
- Minimum
3 m
Closer than this and pixel structure becomes obvious.
- Sweet spot
4.5 m
Where P2 delivers the best clarity-to-cost ratio.
- Maximum
8 m
Beyond this, finer pixel density goes to waste.
Indoor only.
P2 cabinets are sealed for indoor use only — IP30 / IP31. Do not deploy outdoors or in humid, dusty, or open semi-outdoor walkways.
PKR 45,000 – 85,000
Per square foot, supply only — before structure, controller, installation, and calibration.
- Lower band: standard tier-1 cabinets, mainstream brands, typical project size.
- Upper band: premium cabinets, broadcast-grade processors, curve-capable builds, complex installs.
Indicative only — site survey required for a firm quote. Actual price is set by total area, brand, cabinet type, processor, structure, and installation complexity.
Where P2 earns its keep.
Large lobby & atrium walls
Multi-storey corporate lobbies and hotel atriums where viewers approach from 4–8 m.
Retail anchor stores
Big-format retail walls in shopping malls and category-killer flagships viewed from 4 m+.
Conference halls & ballrooms
Stage-side and rear-of-room walls for major events, conferences, and award ceremonies.
Worship halls
Mosque and church projection alternatives where viewers sit 4–10 m away across wide rows.
Airport signage
Departure boards and brand walls in terminals where dwell distance is typically 4–6 m.
Showroom centrepieces
Auto and high-value retail showrooms where the wall is the architectural feature, not the screen-up-close.
What P2 does well.
- Lets you build larger walls than P1.8 within the same budget — 15–20% lower per-square-foot.
- Visually equivalent to P1.8 from 3.5 m and beyond.
- Mature manufacturing across all tier-1 brands — flexible sourcing and good after-sales support.
- Stable thermal performance under long duty cycles in lobbies and concourses.
- Stocks well — modules, spare parts, and replacement cabinets are easy to source domestically.
Honest trade-offs.
- Pixel structure becomes visible inside 2 m — not the right pitch for close-range studio or boardroom use.
- Brightness ceiling is set for indoor lighting — does not handle direct daylight or atrium skylights well without additional lighting controls.
P2 sits between P1.8 (sharper, more expensive) and P2.5 (slightly less detailed, cheaper still). It tends to win the brief whenever total area is large enough that a 15–20% per-square-foot saving makes a real difference and viewing distance is 3.5 m+. For walls under 6 sqm, P1.8 is often the better balance; for walls over 12 sqm, P2 is frequently the rational specification.
Built at scale.
Common screen sizes shipped at P2. Walls outside this range are routine — we will confirm cabinet count and structure at quote stage.
Industries that pick P2.
Large corporate lobbies
Retail anchor stores
Conference halls & ballrooms
Worship halls
Airport signage
Auto & luxury showrooms
P2 questions, answered straight.
- For lobbies with viewers approaching from 4 m or further, P2 is the cost-effective answer. The pixel-density difference vs P1.8 is invisible at typical lobby viewing distance. Choose P1.8 only when the wall is set close to a high-traffic walking lane and viewers will routinely stand within 2.5 m.
Compare nearby pitches before deciding.
Get an honest quote for your P2 project.
Send the use case, location, and rough screen size. We will come back with a realistic per-square-foot range, an honest pitch recommendation, and a clear next step within one working day.
Indicative pricing on this page is supply-only PKR per sqft and excludes structure, controller, installation, and calibration. Site survey required for a firm quote.